The cut end bumper is used to protect butyl and PVC liners from any cut sections of grid. It has a smooth curved side and an open side. The open side has a wider base and a narrower top. It is used in an upside-down position when placing over the diagonal cut sections of grid. It is used in the normal position (opposite) on thicker cross pieces.
50
Subtotal £20.00
V.A.T @ 17.5% £3.50
Total £23.50
SP03-PK50
SP03 Cut End Support Pack 50.
The cut end support is used in the rare event when a section of grid cannot be adequately supported by beams on either side. It is placed over a section of grid and a length of support cord is passed through the bottom two holes which is then anchored outside the pond using either a stake of a ceiling anchor. Ensure the support cord is taught.
50
Subtotal £20.00
V.A.T @ 17.5% £3.50
Total £23.50
SP04-PK25
SP04 Floating Beam Clip Pack 25.
The floating beam clip is used to attach grids to the first and last beams in the pond. It can be used over the ‘star’ configuration in the grid. It is also used to attach any additional support beams to the underside of the grid if required. It is clipped into position using a flat screwdriver – the two curved sections at the base of the clip are clipped into place under the flanged section of the upper part of the beam.
25
Subtotal £12.50
V.A.T @ 17.5% £2.19
Total £14.69
SP05-PK50
SP05 Grid to Grid Clip Pack 50.
The grid to grid clip brings together one grid in a lane with its neighbouring grid. They work in pairs and are clipped in between the tabs on the underside of the grid. One grid to grid clip is placed in one direction, the other in the pair in the other direction. When combined in this way, they draw the two grids together ensuring no separation.
50
Subtotal £20.00
V.A.T @ 17.5% £3.50
Total £23.50
SP06-PK25
SP06 Beam Cleat Pack 25.
The beam cleat is used to cap off the end of the support beam. After the beam is cut to length, without the beam cleat it would pose a threat to the pond liner. The beam cleat has a central hole, through which the support cord is passed.
25
Subtotal £12.50
V.A.T @ 17.5% £2.19
Total £14.69
SP07-PK10
SP07 Foot Pack 10.
The foot is inserted into the bottom of the leg section and rests on the base of the pond. Watch for stones and other sharp objects between the underside of the foot and the liner. The leg is attached to the foot by gently forcing the leg down upon the top of the foot and simultaneously turning the leg until it is in position.
10
Subtotal £23.00
V.A.T @ 17.5% £4.03
Total £27.03
SP08-PK10
SP08 Sliding Support Pack 10.
The sliding support joins the top of the leg to the underside of the beam. It slides along the beam so that a support leg can be positioned at any convenient point. Usually a sliding support will be placed as near to the each end of beam as possible and at approximately every metre in between.
10
Subtotal £23.00
V.A.T @ 17.5% £4.03
Total £27.03
SP09-PK10
SP09 Joiner Pack 10.
The joiner helps position one beam into the next. It is not a load-bearing component. Load is taken by the support leg positioned at the join. The support cord passes through the joiner as shown.
10
Subtotal £8.00
V.A.T @ 17.5% £1.40
Total £9.40
SP10-PK5
SP10 Grid Pack 5.
The grid, made from 30% glass-filled nylon, measures 49cm wide and 59cm long and is 3cm deep. Holes are triangular 14cm x 14cm x 16cm. Beams run underneath the two longest edges and so are spaced 49cm apart. Grids running between two beams form one ‘lane’ of grids.
5
Subtotal £57.00
V.A.T @ 17.5% £9.98
Total £66.98
SP11-1180mm-PK2
SP11 1.18m Long Beams Powder Coated Pack 2.
Used to support grids in place. Can be cut to the desired length or extended by use of the beam joiner. Note that the recess in the top of the beam is designed to take the longest edges of each grid or the tabs on the underside of the outermost grids.
